Do It Yourself Bathtub Setup.
Additional InformationWhat're your beliefs about How to Install a Bathtub Yourself?
Setting up a bathtub isn't specifically brain surgery, however it does need solid plumbing, woodworking, and also often, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is easily accessible, the task can relocate rapidly; if you have to open up a wall surface to eliminate the old tub and also position the new bath tub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will certainly need an assistant to leave the old tub and also embeded in the new one. See to it you have actually qualified on your own for the task and fit attempting it. Rather than working with a professional to take over a halfway-completed job, it is better to take into consideration utilizing one before you start. Chances are you might need a professional plumber to make tube links.
This article will certainly help you mount a new bath tub in your restroom if you have actually already acquired a new bathtub as well as do not need to transform the plan of your previous water supply pipelines.
Your tools as well as material list should make up the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will certainly originate from the pipes. Once the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Before proceeding to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will need decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Secure the tap in place with the producer offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind must be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the location of the boards rather than focusing all the weight onto four small factors.
The following goal is to guarantee that the bathtub is leveled all round. This can be achieved by examining the level as well as adjusting the feet on the bathtub till the level reads level.
To mount faucets, fit the bottom of the furthest flexible faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Switch on the water supply and also inspect all joints as well as new pipework for leakages as well as tighten them if necessary. Load the bath tub and additionally inspect the overflow outlet and the regular outlet for leaks.
Ultimately, repair the bath paneling as defined in the producer's instruction manual. Tiling and also sealing around the bathtub must wait until the bath tub has been used at the very least once as this will certainly settle it into its last position.
Planning for the Setup
To start with, the supporting frame provided with the bath must be fitted (if required) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets system to avoid pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture an inflexible seal, creating the water to pass through the wall between the bath and the tiling, resulting in issues with wetness as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in usage. The sealant can crack fairly very early if you do not think about this motion before sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently offered on the market. It is advisable to fit the tiles making use of water-resistant or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that blog entry on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when exploring the internet. Are you aware of somebody else who is excited by the niche? Be sure promote it. Bless you for your time. Visit us again soon.
Book Appointment